null
RDL

RDL

Result(s) found for “RDL”

No filters applied
  • BSW PART: STGLA1

    Radio Design Labs ST-GLA1

    Gated Line Amplifier

    The ST-GLA1 is a self-gated line amplifier designed to be used in a variety of situations where it is desired to produce an automatically switched line-level signal with integral noise reduction...

    $172.46
  • BSW PART: STRG1

    Radio Design Labs ST-RG1

    Ramp Generator

    The ST-RG1 is a digitally generated 0 to 10 volt Ramp Generator which provides the ideal interface for audio volume control from multiple points with the ST-VCA3. Any number of Up and Down buttons...

    $156.57
  • BSW PART: FPPA20

    Radio Design Labs FP-PA20

    Audio Power Amplifier 8 OHM Output

    The FP-PA20 features a balanced line level input that may be connected unbalanced. A front panel gain control is designed to be adjusted either manually or with a trimming screwdriver. The gain range...

    $226.65
  • BSW PART: STR19B

    Radio Design Labs STR-19B

    Racking Kit

    Easily mount your RDL Stick-On series audio/electrical units into one 19 rack mount system. Holds 10 stick-ons with velcro attachments and allows for uncomplicated cable harnessing. STR-19B mounts up...

    $225.69
  • BSW PART: TXJ2

    Radio Design Labs TX-J2

    Unbalanced Input Transformer

    The RDL TXJ2 is an unbalanced-to-balanced transformer with two unbalanced RCA inputs and one balanced screw terminal output.• Mix two unbalanced audio signals to mono balanced• Combine stereo into...

    $83.96
  • BSW PART: STGCA3

    Radio Design Labs ST-GCA3

    Audio Gain Control Amplifier

    This indispensable device constantly adjusts for changes in input levels, bringing up low levels and reducing gain for high levels to continuously maintain the correct output of your system. It...

    $180.88
  • BSW PART: FPMX4

    Radio Design Labs FP-MX4

    4 Input Mic Line Mixer

    The FP-MX4 is a single-channel audio mixing module featuring four identical inputs. Each input accepts either a mic or line level source. The output section provides four mixing potentiometers...

    $499.80
  • BSW PART: TX1A

    Radio Design Labs TX-1A

    Line Transformer

    The TX1A provides transformer isolation between balanced line and unbalanced input, and sports a level trim pot that adjusts output 4 to 24 dB below input level. Input may be 10 k ohms bridging or...

    $53.39
  • BSW PART: STEQ3

    Radio Design Labs ST-EQ3

    3 Band Equalizer

    Radio Design Labs' Stick-Ons are compact, high-quality audio interface devices that can be directly and discreetly mounted on equipment, under counter tops, or combined in rack mount systems. The...

    $138.24
  • BSW PART: STR19A

    Radio Design Labs STR-19A

    Racking System

    Easily mount your RDL Stick-On series audio/electrical units into one 19 rack mount system. holds 12 stick-ons with velcro attachments and allows for uncomplicated cable harnessing. STR-19A mounts up...

    $189.84
  • BSW PART: TS1D

    Radio Design Labs TS-1D

    Transient Suppressor

    The TS-1D is intended to protect audio input and output circuits from the effects of transients induced on the audio lines.PS24AS power supply sold separately.Main Features:Immunity from...

    $152.41
  • BSW PART: STDA3

    Radio Design Labs ST-DA3

    1X3 Mono Distribution Amplifier

    The ST-DA3 gives you the advantages of an audio distribution amplifier PLUS you can put it where you need it. The ST-DA3 allows bridging of any audio line, adjusting the gain, and driving up to three...

    $201.39