- Specifications:
- Freq. Response:
- 10 Hz to 80 kHz ± 0.5 dB (192 kHz sample rate, re 1 kHz)
- THD + Noise:
- 0.005% max (1 kHz, 22 Hz–22 kHz BW, trim @20, fader @ 0, -10 dBu in)
- Equivalent Input Noise:
- -131 dBV (-129 dBu) max (A-weighting, 76 dB gain, 150 ohm source impedance)
- Processing Engine:
- Highly extensible, full FPGA-based audio processing, 3 FPGAs
- Six-way ARM multiprocessor system
- 64-bit audio processing precision
- Audio Over Ethernet:
- Dante, 32 channels in, 32 channels out
- AES67 compatible
- 1 Gb/s Ethernet, 2 ports, transformer-balanced
- Inputs:
- Mic/Line inputs: 16 total, all fully featured; 6 on full-size XLR, 2 on TA3, 8 on TA5
- Mic-level inputs: (XLR, TA3, TA5): Class-A, discrete differential long-tail pair, 4k ohm input impedance
- Line-level inputs: (XLR, TA3, TA5): active-balanced, 4k ohm input impedance
- AES3 or AES42 available on XLR inputs 1 and 6
- AES42: +10 V, 250 mA available, type-1, auto-ASRC
- Rtn A, B, C (3.5 mm/10-pin): unbalanced 2-channel, 4k ohm input impedance
- Com Rtn 1,2 (TA3, 3.5mm) balanced, 1-channel, 8k ohm input impedance
- External Slate Mic (TA5): balanced, 8k ohm input impedance, menu-selectable 12 V phantom
- Maximum Input Level:
- Mic: +8 dBu (2.0 Vrms)
- Line: +28 dBu (19.5 Vrms)
- Rtn A, B, C: +18 dBu (6.2 Vrms)
- Com Rtn 1, 2: +24 dBu (12.3 Vrms)
- External Slate Mic: +12 dBu (3.2 Vrms)
- High-Pass Filters:
- Adjustable 40 Hz to 320 Hz, 18 dB/oct. 1st stage analog (before preamp), 2nd stage digital
- Limiters:
- Limiters available at all channels, buses, headphones, for all sample rates
- Analog first stage, all subsequent stages digital
- Attack time: 1 ms
- Release time: adjustable, 50 ms to 1000 ms
- Threshold: adjustable, -2 dBFS to -12 dBFS
- Selectable knee: hard or soft
- Selectable ratio: inf:1, 20:1
- Delay:
- Channel Adjustable 0-50 ms
- Output Adjustable 0-500 ms
- Maximum Gain:
- Trim stage (mic input): 76 dB
- Trim stage (line input): 36 dB
- Fader stage: 16 dB
- Bus stage: 16 dB
- Headphone stage: 20 dB
- Mic-to-Line: 108 dB
- Mic-to-Headphone: 112 dB
- Outputs:
- XLR (L, R) active-balanced, 250/3.2k/120 ohms (mic/-10/line)
- Hirose 10-pin (L, R) active-balanced, 250/3.2k/120 ohms (mic/-10/line)
- TA3 (X1-X6) active-balanced, 250/3.2k/120 ohms (mic/-10/line)
- 3.5mm (X7, X8): unbalanced, stereo, 1.8k ohms
- Headphone Outputs:
- ¼”, 3.5 mm
- TA5 (along with mic input pins) for single connection to headset + mic
- High output, 4 ohm output impedance, 400 mW + 400 mW at each connector, all individually driven
- Compatible with headphones of any impedance
- Maximum Output Level (all into 10k load):
- Line: +20 dBu (7.8 Vrms)
- “-10”: +6 dBu (1.5 Vrms)
- Mic: -20 dBu (0.078 Vrms)
- X7/X8 Out: +6 dBu (1.5 Vrms)
- Headphone outputs (¼”, TA-5, X9/X10): +14 dBu (4.0 Vrms)
- A/D converters:
- 32-bit, 120 dB, A-weighted dynamic range typical
- Sampling rates 44.1 kHz, 47.952 kHz, 48 kHz, 48.048 kHz, 88.2 kHz, 96 kHz, 192 kHz
- Digital Outputs:
- AES3 transformer-balanced, in pairs; 1-2 (XLR-L), 3-4 (XLR-R), 5-8 (Hirose 10-pin A)
- 110 ohm, 2 V p-p, AES and S/PDIF compatible
- Recording:
- Internal 256 GB SSD
- Two removable SD Cards
- Simultaneous recording to internal SSD and the two SD cards
- exFAT formatting
- 36 tracks (32 iso channels, 4 buses)
- Broadcast WAV monophonic and polyphonic file format
- 64-bit WAV (RF64) monophonic and polyphonic; support for files > 4 GB
- USB:
- USB-C (USB 3.1 type 1) for file transfer of internal SSD, both SD Cards
- USB-A host for keyboard, external controller, external USB hubs supported for connecting multiple devices Wireless:
- Built-in Bluetooth v5.0 BLE (not supported with rev 1.0 release of SD-Remote)
- Timecode and Sync:
- Modes Supported: Off, Rec Run, Free Run, 24h Run, External, including External Auto-Record and Continuous modes.
- Frame Rates: 23.98, 24, 25, 29.97 DF, 29.97 ND, 30 DF, 30 ND
- Sample/Timecode Accuracy: 0.1 ppm (0.25 frames per 24 hours)
- Timecode Input: 20k ohm impedance, 0.3 V - 3.0 V p-p (–17 dBu - +3 dBu)
- Timecode Output: 75 ohm impedance, 5 V p-p (+12 dBu)
- Word Clock Input: 10k/75 ohm selectable impedance, 1-5 V p-p input sensitivity
- Word Clock Output: 75 ohm impedance, 5 V p-p output, at SR
- Remote Control:
- USB MIDI Control - 3rd party fader controllers
- SD-Remote Android app
- USB Keyboard
- External Timecode Record Trigger
- LCD:
- 320x240, Transflective, excellent sunlight visibility
- Larger touchscreen display available via USB-connected SD-Remote app
- Power:
- External: dual 10-18 V inputs on locking TA4 connectors, pin-4 = (+), pin-1 = (-)
- Dual rear-mount Sony-style L-mount batteries with chargers
- Idle Current Draw: 875 mA @ 12 V (10.5 W)
- Intelligent power-down of unused mic preamps and other internal circuits
- Environmental:
- Operating: -20° C to 60° C, 0 to 90% relative humidity (non-condensing)
- Storage: -40° C to 85° C
- Dimensions (H x W x D):
- 5.1 cm x 32 cm x 20.5 cm ( 2 in x 12.6 in x 8.1 in)
- Weight:
- 5.8 lbs (2.63 kg) unpackaged, without batteries
