null

Ashly PEMA4125

Ashly

BSW PART:
PEMA4125

Network Power Amp 4 x 125W at 4 Ohms and 25V Constant Voltage with 8x8 Protea DSP

$2,849.00 $3,561.00
You save $712.00

In many system installations, you can replace an entire rack of pro audio gear—with a single Pema™. Pema™ with it’s new sleek look, is a Protea-Equipped Media Amplifier—either 4 or 8-channel at 250 Watts or 125 Watts per channel. Pema is a matrix mixer—all Pema models have a full 8-in x 8-out matrix mixer, where any input can be assigned to any output or outputs. Pema is a digital signal processor. In addition to the full Protea™ suite of DSP settings, we have added four new features to Pema—gain sharing automatic microphone mixing, an automatic feedback suppressor, ambient noise detection and adjustment and a real-time clock with an event scheduler. Pema features Ashly’s energy efficient Class-D amplifier topology with a switching power supply—and is over 80% energy efficient out of the box. Maximize the energy efficiency of your audio system by using the event scheduler to either put the Pema in stand-by mode or turn it off completely. Pema is offered in separate Low-Z, 25V, 70V, or 100V constant voltage models. Pema is also offered with 240V line voltage in either Low-Z or 100V output for International customers.

$2,849.00 $3,561.00
You save $712.00

Free Shipping

Out of stock

Add to quote
Qualifies for free shipping
  • Main Features:
  • CobraNet® and Dante® network audio fully supported
  • FIR Filter capable
  • 8-in x 8-out sophisticated matrix mixing
  • 8 built-in mic pre’s
  • Gain sharing automatic microphone mixing (Automixer)
  • Automatic feedback suppression
  • Ambient noise compensation
  • Dedicated telephone/PBX input
  • Dual RCA and balanced euroblock inputs
  • Post DSP AUX line level outputs
  • Stereo summed to mono
  • Event scheduling (RTC)
  • Adjustable HP/LP filters
  • Built-in pink/white noise & sine wave generator
  • Full suite of Ashly Protea™ DSP
  • Hot-plug DSP placement
  • 96kHz or 48kHz sample rate
  • 32-Bit SHARC DSP
  • 24-Bit A/D–D/A audio resolution
  • 15V phantom power for mic inputs
  • Full control using Ashly software over 10/100 baseT Ethernet
  • Easy and intuitive user interface
  • Automatic DHCP network IP configuration
  • Euroblock connectors for preset recall, DC remote level control and serial data control
  • External control via Ashly standard wall remotes, Ashly Ethernet wall remotes or Ashly Remote iPad® App
  • Level control via variable DC control voltage
  • Stand-By mode activation via contact closure
  • Multi-level Security
  • Safety/Compliance: cTUVus, CE, FCC, RoHS
  • Specifications:
  • Input Sensitivity (Low Z models): 3.2dBu (4125/8125) 6.2dBu (4250/8250) 7.2dBu (70V/100V models)
  • Voltage Gain: 26dB (Low Z models), 32dB (70V models) 35dB (100V models)
  • Damping Factor: >250 (8 Ohm load, <1kHz)
  • Distortion:
  • <0.5% (SMPTE, typical)
  • <0.5% (THD-N, typical, 8 Ohm, 10dB below rated power, 20Hz–20kHz)
  • Channel Separation: -80dB (dB from full output, 1kHz)
  • Frequency Response: 20Hz–20kHz, +/-1dB
  • Mic/Line Input Impedance: 4.8k Ohms
  • Mic/Line Maximum Input Level: +21dBu
  • Mic/Line Preamp Gain: 0, +20dB, +40dB, +60dB
  • Mic/Line Phantom Power: +15V, switchable ch. 1-4, 5-8
  • Summed Mono:
  • 3.16k Ohm (Input Impedance)
  • +11dBu (Maximum Input Level)
  • Channel 1 TEL-PBX:
  • 3.9k Ohm (Input Impedance)
  • +21dBu (Maximum Input Level)
  • Preamp Output Maximum Level: +8dBu
  • AUX Output Maximum Level: +20dBu
  • Environmental: 40-120 deg. F, (4-49 deg, C) (noncondensing)
  • Audio Connections:
  • 1 Euro connector balanced input, selectable for Mic, Line or TEL-PBX
  • 7 Euro connector balanced inputs, software selectable for Mic or Line
  • 8 pairs of unbalanced, summed mono RCA connectors optimized for consumer line level (-10dBV nominal) devices
  • 8 Euro connector Preamp/Aux outputs
  • 4 or 8 Euro connector speaker outputs
  • CobraNet® and Dante® Digital I/O options
  • Power Requirements:
  • AC Mains: 120VAC or 240VAC, ±10% 50–60Hz
  • Power Cable Connector: 15A Edison, 3-Prong IEC
  • Weights and Dimensions:
  • Dimensions: 19” W x 3.50” H x 16.84” D (483mm x 89mm x 428mm)
  • Airflow: IN through sides, OUT through front
  • Unit Weight:
  • 4125/4250: 23.5 lbs (10.7 kg)
  • 8125/8250: 25 lbs (11.3 kg)
  • Shipping Weight:
  • 4125/4250: 30.9 lbs (14 kg)
  • 8125/8250: 32.3 lbs (14.7 kg)
  • Environmental: 40-120 deg. F, (4-49 deg, C) (noncondensing)