- Main Features:
- From 8x8 to 32x32 channels of Dante® audio-over-IP with AES67 interoperability
- 44.1, 48 or 96kHz sample rates with 32bit A/D and D/A conversion
- Balanced microphone/line level inputs with level range of -60 to +24dBu
- Switchable +48V phantom power on each input
- Balanced line outputs with level of 0 to +24dBu
- 3.81mm Terminal Block terminations, DB-25 or RJ45/StudioHub+GPIO
- RGB front panel LEDs provide per channel metering and stream status
- Built-in web server for configuration and monitoring
- Dual RJ-45 network jacks can be operated in redundant or switched mode
- Built-in universal 90-260VAC 50/60Hz power supply
- Auxiliary +12VDC input for redundant power supply
- GPIO units provide 5 relay isolated outputs and 5 opto-isolated inputs
- Specifications:
- DANTE INPUT/OUTPUT
- Type 100/1000Mb Ethernet
- Connector Dual RJ-45 operable as redundant Dante or as a network switch
- Channels
- 8.8M – 8 input and 8 output channels
- 16.16M – 16 input and 16 output channels
- 32.32M – 32 input and 32 output channels
- 16.0M – 16 input and 0 output
- 0.16L – 0 input and 16 output
- 32.0M – 32 input and 0 output
- 0.32L – 0 input and 32 output
- Audio formats 16, 24 and 32 bits per sample
- Sample Rate 44.1kHz, 48kHz, 96kHz
- Latency 0.15, 0.25, 0.5, 1.0 and 5.0ms
- ANALOG MIC/LINE INPUT
- Type Balanced
- Input Level -60 to +24dBu in 1dBu steps
- EIN -126 dBu Equivalent Input Noise @ -26dBu level setting
- Phantom Power +48V @ 10mA per channel max, software switchable. Max draw per 16 mic inputs must be 80mA or less
- A/D converter 32 bit over sampling
- Input Impedance 10K ohms
- Dynamic Range [1] >114dB
- THD+N [2] < -97dB
- Frequency Response
- @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-3.0dB
- @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
- Connectors 3.81mm Terminal Block, DB-25 or RJ-45/StudioHub+GPIO
- ANALOG LINE OUTPUT
- Type Balanced
- Output Level -10 to +24dBu in 1dBu steps
- D/A converter 32 bit over sampling
- Load Impedance 2K ohms or greater
- Dynamic Range [1] >114dB
- THD+N [2] < -100dB
- Frequency Response
- @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-0.25dB
- @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
- Connectors 3.81mm Terminal Block, DB-25 or RJ-45/StudioHub+GPIO
- GPIO
- Opto-isolated Inputs
- Isolation 2,500 VACRMS
- Input Drive 4mA typical with internal 5V supply and internal 1K current limiting resistor
- Input Voltage Range Between 3V and 24V. Add external resistor above 24V to limit current
- Relay-isolated Outputs
- Isolation 1,500 VAC
- Contact Rating Up to 60 VDC/60VAC and 350mA, 600mW maximum
- Opto-isolated Inputs
- LATENCY (48kHz, L24)
- Analog Input to Dante Transmit 770.21 μs
- Dante Receive to Analog Output 713.05 μs
- POWER
- Built in Power supply 90-260VAC, 47-63Hz with IEC C-14 AC inlet
- Redundant Power supply (Optional) Supplied using an external +12VDC, 60W power supply with 2.1mm locking plug
- ASI part number for power supply: PWR1101
- Power supplies function independently; use DC only, AC only or both at the same time for fail-over redundancy
- REGULATORY
- FCC Part 48 Class A (US)
- CE Mark (EN55022 Class A EN55024)
- RoHS Compliant
- GENERAL
- Dimensions 1 RU, 19”(482mm) W x 6”(152mm) L x 1.75”(44mm) H
- Weight 5 lb (2.2kg) max (32.32M)
- Operating Temperature 0C to 50C in free air