null
AudioScience IYO-DANTE-32.32M

AudioScience IYO-DANTE-32.32M

AUDIOSCIEN

BSW PART:
IYO-DANTE-32-32
More Talkshow Systems and Components More AudioScience
$4,613.00

The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. Several models provide various configurations of balanced analog audio inputs and outputs. Each input accommodates microphone through line level signals with a range of -60 to +24dBu. +48V phantom power is individually switchable on each input. Output levels are configurable up to +24dBu. RGB LEDs on the Iyo’s front panel show per channel audio levels and streaming status. The Iyo family features an embedded web server, allowing configuration and monitoring of input and output levels. Routing is achieved using the Dante Controller. Power is provided from a built-in universal AC power supply. Redundant power is available using an external 12VDC supply via a locking 2.1mm jack. All units can also be operated in AES67 interoperability mode.

$4,613.00

Free Shipping

Out of stock

Add to quote
Qualifies for free shipping

  • Main Features:
  • From 8x8 to 32x32 channels of Dante® audio-over-IP with AES67 interoperability
  • 44.1, 48 or 96kHz sample rates with 32bit A/D and D/A conversion
  • Balanced microphone/line level inputs with level range of -60 to +24dBu
  • Switchable +48V phantom power on each input
  • Balanced line outputs with level of 0 to +24dBu
  • 3.81mm Terminal Block terminations, DB-25 or RJ45/StudioHub+GPIO
  • RGB front panel LEDs provide per channel metering and stream status
  • Built-in web server for configuration and monitoring
  • Dual RJ-45 network jacks can be operated in redundant or switched mode
  • Built-in universal 90-260VAC 50/60Hz power supply
  • Auxiliary +12VDC input for redundant power supply
  • GPIO units provide 5 relay isolated outputs and 5 opto-isolated inputs
  • Specifications:
  • DANTE INPUT/OUTPUT
    • Type 100/1000Mb Ethernet
    • Connector Dual RJ-45 operable as redundant Dante or as a network switch
    • Channels
      • 8.8M – 8 input and 8 output channels
      • 16.16M – 16 input and 16 output channels
      • 32.32M – 32 input and 32 output channels
      • 16.0M – 16 input and 0 output
      • 0.16L – 0 input and 16 output
      • 32.0M – 32 input and 0 output
      • 0.32L – 0 input and 32 output
    • Audio formats 16, 24 and 32 bits per sample
    • Sample Rate 44.1kHz, 48kHz, 96kHz
    • Latency 0.15, 0.25, 0.5, 1.0 and 5.0ms
  • ANALOG MIC/LINE INPUT
    • Type Balanced
    • Input Level -60 to +24dBu in 1dBu steps
    • EIN -126 dBu Equivalent Input Noise @ -26dBu level setting
    • Phantom Power +48V @ 10mA per channel max, software switchable. Max draw per 16 mic inputs must be 80mA or less
    • A/D converter 32 bit over sampling
    • Input Impedance 10K ohms
    • Dynamic Range [1] >114dB
    • THD+N [2] < -97dB
    • Frequency Response
      • @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-3.0dB
      • @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
    • Connectors 3.81mm Terminal Block, DB-25 or RJ-45/StudioHub+GPIO
  • ANALOG LINE OUTPUT
    • Type Balanced
    • Output Level -10 to +24dBu in 1dBu steps
    • D/A converter 32 bit over sampling
    • Load Impedance 2K ohms or greater
    • Dynamic Range [1] >114dB
    • THD+N [2] < -100dB
    • Frequency Response
      • @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-0.25dB
      • @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
    • Connectors 3.81mm Terminal Block, DB-25 or RJ-45/StudioHub+GPIO
  • GPIO
    • Opto-isolated Inputs
      • Isolation 2,500 VACRMS
      • Input Drive 4mA typical with internal 5V supply and internal 1K current limiting resistor
      • Input Voltage Range Between 3V and 24V. Add external resistor above 24V to limit current
    • Relay-isolated Outputs
      • Isolation 1,500 VAC
      • Contact Rating Up to 60 VDC/60VAC and 350mA, 600mW maximum
  • LATENCY (48kHz, L24)
    • Analog Input to Dante Transmit 770.21 μs
    • Dante Receive to Analog Output 713.05 μs
  • POWER
    • Built in Power supply 90-260VAC, 47-63Hz with IEC C-14 AC inlet
    • Redundant Power supply (Optional) Supplied using an external +12VDC, 60W power supply with 2.1mm locking plug
    • ASI part number for power supply: PWR1101
    • Power supplies function independently; use DC only, AC only or both at the same time for fail-over redundancy
  • REGULATORY
    • FCC Part 48 Class A (US)
    • CE Mark (EN55022 Class A EN55024)
    • RoHS Compliant
  • GENERAL
    • Dimensions 1 RU, 19”(482mm) W x 6”(152mm) L x 1.75”(44mm) H
    • Weight 5 lb (2.2kg) max (32.32M)
    • Operating Temperature 0C to 50C in free air