The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. Several models provide various configurations of balanced analog audio inputs and outputs. Each input accommodates microphone through line level signals with a range of -60 to +24dBu. +48V phantom power is individually switchable on each input. Output levels are configurable up to +24dBu. RGB LEDs on the Iyo’s front panel show per channel audio levels and streaming status. The Iyo family feature an embedded web server, allowing configuration and monitoring of input and output levels. Routing is achieved using the Dante Controller. Power is provided from a built-in universal AC power supply. Redundant power is available using an external 12VDC supply via a locking 2.1mm jack. All units can also be operated in AES67 interoperability mode.
Main Features:
• Up to 32 channels of Dante audio-over-IP with AES67 interoperability
• 48 or 96kHz sample rates
• Balanced microphone/line level inputs with level range of -60 to +24dBu
• Balanced line level outputs with level range of 0 to +24dBu
• Switchable +48V phantom power on each input
• RGB front panel LEDs provide per channel metering and stream status
• Built in web server provides audio level configuration and monitoring
• 1U rack-mount unit
• Dual RJ-45 network jacks can be operated in redundant or switched mode
• Built-in universal 90-260VAC power supply
• Auxiliary +12VDC input provides power supply redundancy
• Dante Domain Manager "DDM" ready
• Public control protocol
Specifications:
DANTE INPUT/OUTPUT:
• Type: 100/1000Mb Ethernet
• Connector: Dual RJ-45 operable as redundant Dante or as a network switch
• Channels: 16.0M – 16 input and 0 output
• Audio formats: 16, 24 and 32 bits per sample
• Sample Rate: 48kHz, 96kHz
• Latency: 0.15, 0.25, 0.5, 1.0 and 5.0ms
ANALOG MIC/LINE INPUT
• Type: Balanced
• Input Level: -60 to +24dBu in 1dBu steps
• EIN: -126 dBu Equivalent Input Noise @ -26dBu level setting
• Phantom Power: +48V @ 10mA per channel max , software switchable
• A/D converter: 32 bit over sampling
• Input Impedance: 10K ohms
• Dynamic Range [1]: >114dB
• THD+N [2]: < -97dB
Frequency Response:
• @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-0.5dB
• @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-2.0dB
• Connectors: 3.81mm Terminal Block, DB-25 or RJ-45/StudioHub+GPIO
ANALOG LINE OUTPUT
• Type: Balanced
• Output Level: -10 to +24dBu in 1dBu steps
• D/A converter: 32 bit over sampling
• Load Impedance: 2K ohms or greater
• Dynamic Range [1]: >114dB
• THD+N [2]: < -100dB
Frequency Response:
• @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-0.25dB
• @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
• Connectors: 3.81mm Terminal Block, DB-25 or RJ-45/StudioHub+GPIO
GPIO:
Opto-isolated Inputs:
• Isolation: 2,500 VACRMS
• Input Drive: 4mA typical with internal 5V supply and internal 1K current limiting resistor
• Input Voltage Range: Between 3V and 24V. Add external resistor above 24V to limit current.
Relay-isolated Outputs:
• Isolation: 1,500 VAC
• Contact Rating: Up to 60 VDC/60VAC and 350mA, 600mW maximum
LATENCY (48kHz, L24):
• Analog Input to Dante Transmit: 770.21 μs
• Dante Receive to Analog Output: 713.05 μs
POWER:
• Built in Power supply: 90-260VAC, 47-63Hz with IEC C-14 AC inlet
• Redundant Power supply (Optional): Supplied using an external +12VDC, 60W power supply with 2.1mm locking plug
REGULATORY:
• FCC Part 48 Class A (US)
• CE Mark (EN55022 Class A EN55024)
• RoHS Compliant
GENERAL:
• Dimensions: 1 RU, 19”(482mm) W x 6”(152mm) L x 1.75”(44mm) H
• Weight: 5 lb (2.2kg) max (32.32M)
• Operating Temperature: 0C to 40C in free air
